คำอธิบาย
ตัวควบคุมสเต็ปเปอร์มอเตอร์ ตัวควบคุมเซอร์โวมอเตอร์ การควบคุม Pulse การควบคุมความเร็ว การควบคุมการเคลื่อนที่แบบแกนเดียว ตั้งโปรแกรมได้
- Control step 1-1000
- Speed: control servo 100-2500
- Step reverse servo 0-3000
Operation Mode
- 0: Speed mode, the speed can be adjusted at any time, and it can automatically go back and forth between 2 limits
- 1: Fixed-length mode can run a fixed distance, number of turns, and angle.
- 2: Continuous mode The walking mode is the same as the fixed-length mode, with the addition of the number of cycles.
- 3: Round-trip mode The walking method is the same as the fixed length, plus automatic reverse and round-trip times
- 4: Timing mode You can set how long to go, and the running mode is the same as the speed mode.
การใช้งาน
1.หน้าจอดิจิตอลจะแสดงค่าความเร็วปัจจุบันเป็นรอบต่อนาที
2.การตั้งค่าพารามิเตอร์:
Parameter setting: In the stop installation state, press SET and holdKey,
ACC appears, and then press SET The parameter value of ACC appears in the key, press -V-
-V- and -^- Key to modify, press after modification
Confirm, return to ACC status, press SET tAb appears, then press Modo appears, then Model appears, then press back to ACC parameter settings The same as ACC, press
-^- Key exit
The parameter is set to the stop state,
ACC
- การตั้งค่าการเร่งความเร็ว (1-99) 1 คือเร็วที่สุด ค่าเริ่มต้นคือ 5
tAb
- subdivision number setting (1-64) This value is based on the settings on the drive, and should be consistent with the drive settings. When the settings are consistent, the displayed speed is real. Actual speed, the default value is 10.
Mode 0
mode 0 (0-1) is set to 0 when power-up is stopped, and when power-up is set to 1, it will run. The default value is 0.
Mode 1
mode 1 (0-4) default value 0
- 0 Terminal 3 is turned on to start, turned off to stop, the direction is terminal 4 is turned on to forward, turned off to reverse
- 1 Click on terminal 3 to start, and then click to stop. The direction is terminal 4 and click to stop.
- 2 Click on terminal 3 to start, and click on terminal 4 to stop
- 3 Terminal 3, click forward to start, then click stop, press terminal 4, click reverse to start, and then click stop.
- 4 Terminal 3 is turned on to forward start, disconnected to stop, terminal 4 is turned on to reverse start, disconnected to stop.
Mode 2
mode 2 (0-3) 0 speed control, 1 fixed-length control, 2 continuous control, 3 round-trip control, default value is 0
In fixed-length mode, press the stop button to set P-01 in the stop state, and press and hold the stop button to have d1A, d1b
In continuous mode and round-trip mode, the stop state is set according to the stop state P-01, P-02, P-03
In the speed control mode and round-trip mode, the X1 and X2 limits are valid, and the direction will be reversed when encountered.
- P-01 length value, number of pulses = P-01*d1a/d1b
doubb: Magnification setting default 1 0-1000 rpm adjustable - P-02 delay value, in milliseconds
Set to 2 0-2000 rpm adjustable - P-03 frequency value, continuous operation frequency value
Set to 3 0-3000 rpm adjustable
Terminals
- V+ DC24V
- GND
- Start/Stop
- Forward/Reverse
- FRE
- Direction
- Pulse
- Opto +DC5V
Dimensions: Length*width*height: 112*60*52
Panel size: 98mm*56mm
ในชุดประกอบด้วย
- กล่องควบคุมสเต็ปเปอร์มอเตอร์ Stepper Motor Programmable Motion Control
รีวิว
ยังไม่มีบทวิจารณ์